Titles of Regulations: 9VAC5-20. General Provisions (amending 9VAC5-20-21).

9VAC5-40. Existing Stationary Sources (amending 9VAC5-40-5970).

9VAC5-50. New and Modified Stationary Sources (amending 9VAC5-50-400, 9VAC5-50-410).

9VAC5-60. Hazardous Air Pollutant Sources (amending 9VAC5-60-60, 9VAC5-60-90).

Statutory Authority:

§ 10.1-1308 of the Code of Virginia; §§ 108, 109, 110, and 182 of the Clean Air Act; 40 CFR Parts 50, 53, and 58 (9VAC5-20-21).

§ 10.1-1308 of the Code of Virginia; §§ 110, 111, 123, 129, 171, 172, and 182 of the Clean Air Act; 40 CFR Parts 51 and 60 (9VAC5-40-5970, 9VAC5-50-400, 9VAC5-50-410, 9VAC5-60-60, 9VAC5-60-90).

Effective Date: November 11, 2020.

Agency Contact: Karen G. Sabasteanski, Department of Environmental Quality, 1111 East Main Street, Suite 1400, P.O. Box 1105, Richmond, VA 23218, telephone (804) 698-4423, FAX (804) 698-4178, or email karen.sabasteanski@deq.virginia.gov.

Summary:

The amendments (i) update references to certain federal regulations to reflect the Code of Federal Regulations as published on July 1, 2020; (ii) add two new source performance standards, Subpart XXX (Municipal Solid Waste Landfills that Commenced Construction, Reconstruction, or Modification After July 17, 2014) and Subpart OOOOa (Crude Oil and Natural Gas Facilities for which Construction, Modification, or Reconstruction Commenced after September 18, 2015) of 40 CFR Part 60; (iii) remove an outdated reference to a specific version of a federal code citation relating to Article 43.1 (9VAC5-40-5925 et seq.) of 9VAC5-40; and (iv) update and correct an internal reference to a federal standard affecting a specific stationary source (landfills).

9VAC5-20-21. Documents incorporated by reference.

A. The Administrative Process Act and Virginia Register Act provide that state regulations may incorporate documents by reference. Throughout these regulations, documents of the types specified below have been incorporated by reference.

1. United States Code.

2. Code of Virginia.

3. Code of Federal Regulations.

4. Federal Register.

5. Technical and scientific reference documents.

Additional information on key federal regulations and nonstatutory documents incorporated by reference and their availability may be found in subsection E of this section.

B. Any reference in these regulations to any provision of the Code of Federal Regulations (CFR) shall be considered as the adoption by reference of that provision. The specific version of the provision adopted by reference shall be that contained in the CFR (2016) (2020) in effect July 1, 2016 2020. For the purposes of Article 43.1 (9VAC5-40-5925 et seq.) of 9VAC5-40 (Existing Stationary Sources), EPA regulations promulgated at Subpart Cf (40 CFR 60.30f et seq., Emission Guidelines and Compliance Times for Municipal Solid Waste Landfills) of 40 CFR Part 60, as published in the Federal Register of August 29, 2016 (81 FR 59276) and effective on October 28, 2016, is the version incorporated by reference into this article and Article 43.1. In making reference to the Code of Federal Regulations, 40 CFR Part 35 means Part 35 of Title 40 of the Code of Federal Regulations; 40 CFR 35.20 means § 35.20 in Part 35 of Title 40 of the Code of Federal Regulations.

C. Failure to include in this section any document referenced in the regulations shall not invalidate the applicability of the referenced document.

D. Copies of materials incorporated by reference in this section may be examined by the public at the central office of the Department of Environmental Quality, 1111 East Main Street, Suite 1400, Richmond, Virginia, between 8:30 a.m. and 4:30 p.m. of each business day.

E. Information on federal regulations and nonstatutory documents incorporated by reference and their availability may be found below in this subsection.

1. Code of Federal Regulations.

a. The provisions specified below from the Code of Federal Regulations (CFR) are incorporated herein by reference.

(1) 40 CFR Part 50 -- National Primary and Secondary Ambient Air Quality Standards.

(a) Appendix A-1 -- Reference Measurement Principle and Calibration Procedure for the Measurement of Sulfur Dioxide in the Atmosphere (Ultraviolet Fluorescence Method).

(b) Appendix A-2 -- Reference Method for the Determination of Sulfur Dioxide in the Atmosphere (Pararosaniline Method).

(c) Appendix B -- Reference Method for the Determination of Suspended Particulate Matter in the Atmosphere (High-Volume Method).

(d) Appendix C -- Measurement Principle and Calibration Procedure for the Continuous Measurement of Carbon Monoxide in the Atmosphere (Non-Dispersive Infrared Photometry).

(e) Appendix D -- Measurement Principle and Calibration Procedure for the Measurement of Ozone in the Atmosphere.

(f) Appendix E -- Reserved.

(g) Appendix F -- Measurement Principle and Calibration Procedure for the Measurement of Nitrogen Dioxide in the Atmosphere (Gas Phase Chemiluminescence).

(h) Appendix G -- Reference Method for the Determination of Lead in Suspended Particulate Matter Collected from Ambient Air.

(i) Appendix H -- Interpretation of the National Ambient Air Quality Standards for Ozone.

(j) Appendix I -- Interpretation of the 8-Hour Primary and Secondary National Ambient Air Quality Standards for Ozone.

(k) Appendix J -- Reference Method for the Determination of Particulate Matter as PM₁₀ in the Atmosphere.

(l) Appendix K -- Interpretation of the National Ambient Air Quality Standards for Particulate Matter.

(m) Appendix L -- Reference Method for the Determination of Fine Particulate Matter as PM_2.5 in the Atmosphere.

(n) Appendix M -- Reserved.

(o) Appendix N -- Interpretation of the National Ambient Air Quality Standards for PM_2.5.

(p) Appendix O -- Reference Method for the Determination of Coarse Particulate Matter as PM in the Atmosphere.

(q) Appendix P -- Interpretation of the Primary and Secondary National Ambient Air Quality Standards for Ozone.

(r) Appendix Q -- Reference Method for the Determination of Lead in Suspended Particulate Matter as PM₁₀ Collected from Ambient Air.

(s) Appendix R -- Interpretation of the National Ambient Air Quality Standards for Lead.

(t) Appendix S -- Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Nitrogen (Nitrogen Dioxide).

(u) Appendix T -- Interpretation of the Primary National Ambient Air Quality Standards for Oxides of Sulfur (Sulfur Dioxide).

(v) Appendix U -- Interpretation of the Primary and Secondary National Ambient Air Quality Standards for Ozone.

(2) 40 CFR Part 51 -- Requirements for Preparation, Adoption, and Submittal of Implementation Plans.

(a) Appendix M -- Recommended Test Methods for State Implementation Plans.

(b) Appendix S -- Emission Offset Interpretive Ruling.

(c) Appendix W -- Guideline on Air Quality Models (Revised).

(d) Appendix Y -- Guidelines for BART Determinations Under the Regional Haze Rule.

(3) 40 CFR Part 55 -- Outer Continental Shelf Air Regulations, except for §§ 55.5, 55.11, and 55.12.

(4) 40 CFR Part 58 -- Ambient Air Quality Surveillance.

Appendix A -- Quality Assurance Requirements for SLAMS, SPMs and PSD Air Monitoring.

(5) 40 CFR Part 59 -- National Volatile Organic Compound Emission Standards for Consumer and Commercial Products.

(a) Subpart C -- National Volatile Organic Compound Emission Standards for Consumer Products.

(b) Subpart D -- National Volatile Organic Compound Emission Standards for Architectural Coatings, Appendix A -- Determination of Volatile Matter Content of Methacrylate Multicomponent Coatings Used as Traffic Marking Coatings.

(6) 40 CFR Part 60 -- Standards of Performance for New Stationary Sources.

The specific provisions of 40 CFR Part 60 incorporated by reference are found in Article 5 (9VAC5-50-400 et seq.) of Part II of 9VAC5-50 (New and Modified Stationary Sources).

(7) 40 CFR Part 61 -- National Emission Standards for Hazardous Air Pollutants.

The specific provisions of 40 CFR Part 61 incorporated by reference are found in Article 1 (9VAC5-60-60 et seq.) of Part II of 9VAC5-60 (Hazardous Air Pollutant Sources).

(8) 40 CFR Part 63 -- National Emission Standards for Hazardous Air Pollutants for Source Categories.

The specific provisions of 40 CFR Part 63 incorporated by reference are found in Article 2 (9VAC5-60-90 et seq.) of Part II of 9VAC5-60 (Hazardous Air Pollutant Sources).

(9) 40 CFR Part 64 -- Compliance Assurance Monitoring.

(10) 40 CFR Part 72 -- Permits Regulation.

(11) 40 CFR Part 73 -- Sulfur Dioxide Allowance System.

(12) 40 CFR Part 74 -- Sulfur Dioxide Opt-Ins.

(13) 40 CFR Part 75 -- Continuous Emission Monitoring.

(14) 40 CFR Part 76 -- Acid Rain Nitrogen Oxides Emission Reduction Program.

(15) 40 CFR Part 77 -- Excess Emissions.

(16) 40 CFR Part 78 -- Appeal Procedures for Acid Rain Program.

(17) 40 CFR Part 152 Subpart I -- Classification of Pesticides.

(18) 49 CFR Part 172 -- Hazardous Materials Table. Special Provisions, Hazardous Materials Communications, Emergency Response Information, and Training Requirements, Subpart E, Labeling.

(19) 29 CFR Part 1926 Subpart F -- Fire Protection and Prevention.

b. Copies may be obtained from Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954; telephone (202) 783-3238.

2. U.S. Environmental Protection Agency.

a. The following documents from the U.S. Environmental Protection Agency are incorporated herein by reference:

(1) Reich Test, Atmospheric Emissions from Sulfuric Acid Manufacturing Processes, Public Health Service Publication No. PB82250721, 1980.

(2) Compilation of Air Pollutant Emission Factors (AP-42). Volume I: Stationary and Area Sources, stock number 055-000-00500-1, 1995; Supplement A, stock number 055-000-00551-6, 1996; Supplement B, stock number 055-000-00565, 1997; Supplement C, stock number 055-000-00587-7, 1997; Supplement D, 1998; Supplement E, 1999.

(3) "Guidelines for Determining Capture Efficiency" (GD-35), Emissions Monitoring and Analysis Division, Office of Air Quality Planning and Standards, January 9, 1995.

b. Copies of the document identified in subdivision E 2 a (1) of this section, and Volume I and Supplements A through C of the document identified in subdivision E 2 a (2) of this section, may be obtained from U.S. Department of Commerce, National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161; telephone 1-800-553-6847. Copies of Supplements D and E of the document identified in subdivision E 2 a (2) of this section may be obtained online from EPA's Technology Transfer Network at http://www.epa.gov/ttn/index.html. Copies of the document identified in subdivision E 2 a (3) of this section are only available online from EPA's Technology Transfer Network at http://www.epa.gov/ttn/emc/guidlnd.html.

3. United States government.

a. The following document from the United States government is incorporated herein by reference: Standard Industrial Classification Manual, 1987 (U.S. Government Printing Office stock number 041-001-00-314-2).

b. Copies may be obtained from Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954; telephone (202) 512-1800.

4. American Society for Testing and Materials (ASTM).

a. The documents specified below from the American Society for Testing and Materials are incorporated herein by reference.

(1) D323-99a, "Standard Test Method for Vapor Pressure of Petroleum Products (Reid Method)."

(2) D97-96a, "Standard Test Method for Pour Point of Petroleum Products."

(3) D129-00, "Standard Test Method for Sulfur in Petroleum Products (General Bomb Method)."

(4) D388-99, "Standard Classification of Coals by Rank."

(5) D396-98, "Standard Specification for Fuel Oils."

(6) D975-98b, "Standard Specification for Diesel Fuel Oils."

(7) D1072-90(1999), "Standard Test Method for Total Sulfur in Fuel Gases."

(8) D1265-97, "Standard Practice for Sampling Liquefied Petroleum (LP) Gases (Manual Method)."

(9) D2622-98, "Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry."

(10) D4057-95(2000), "Standard Practice for Manual Sampling of Petroleum and Petroleum Products."

(11) D4294-98, "Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy."

(12) D523-89, "Standard Test Method for Specular Gloss" (1999).

(13) D1613-02, "Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer and Related Products" (2002).

(14) D1640-95, "Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature" (1999).

(15) E119-00a, "Standard Test Methods for Fire Tests of Building Construction Materials" (2000).

(16) E84-01, "Standard Test Method for Surface Burning Characteristics of Building Construction Materials" (2001).

(17) D4214-98, "Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films" (1998).

(18) D86-04b, "Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure" (2004).

(19) D4359-90, "Standard Test Method for Determining Whether a Material is a Liquid or a Solid" (reapproved 2000).

(20) E260-96, "Standard Practice for Packed Column Gas Chromatography" (reapproved 2001).

(21) D3912-95, "Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants" (reapproved 2001).

(22) D4082-02, "Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants."

(23) F852-99, "Standard Specification for Portable Gasoline Containers for Consumer Use" (reapproved 2006).

(24) F976-02, "Standard Specification for Portable Kerosine and Diesel Containers for Consumer Use."

(25) D4457-02, "Standard Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph" (reapproved 2008).

(26) D3792-05, "Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph."

(27) D2879-97, "Standard Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope" (reapproved 2007).

b. Copies may be obtained from American Society for Testing Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; telephone (610) 832-9585.

5. American Petroleum Institute (API).

a. The following document from the American Petroleum Institute is incorporated herein by reference: Evaporative Loss from Floating Roof Tanks, API MPMS Chapter 19, April 1, 1997.

b. Copies may be obtained from American Petroleum Institute, 1220 L Street, Northwest, Washington, DC 20005; telephone (202) 682-8000.

6. American Conference of Governmental Industrial Hygienists (ACGIH).

a. The following document from the ACGIH is incorporated herein by reference: 1991-1992 Threshold Limit Values for Chemical Substances and Physical Agents and Biological Exposure Indices (ACGIH Handbook).

b. Copies may be obtained from ACGIH, 1330 Kemper Meadow Drive, Suite 600, Cincinnati, OH 45240; telephone (513) 742-2020.

7. National Fire Prevention Association (NFPA).

a. The documents specified below from the National Fire Prevention Association are incorporated herein by reference.

(1) NFPA 385, Standard for Tank Vehicles for Flammable and Combustible Liquids, 2000 Edition.

(2) NFPA 30, Flammable and Combustible Liquids Code, 2000 Edition.

(3) NFPA 30A, Code for Motor Fuel Dispensing Facilities and Repair Garages, 2000 Edition.

b. Copies may be obtained from the National Fire Prevention Association, One Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101; telephone (617) 770-3000.

8. American Society of Mechanical Engineers (ASME).

a. The documents specified below from the American Society of Mechanical Engineers are incorporated herein by reference.

(1) ASME Power Test Codes: Test Code for Steam Generating Units, Power Test Code 4.1-1964 (R1991).

(2) ASME Interim Supplement 19.5 on Instruments and Apparatus: Application, Part II of Fluid Meters, 6th edition (1971).

(3) Standard for the Qualification and Certification of Resource Recovery Facility Operators, ASME QRO-1-1994.

b. Copies may be obtained from the American Society of Mechanical Engineers, Three Park Avenue, New York, NY 10016; telephone (800) 843-2763.

9. American Hospital Association (AHA).

a. The following document from the American Hospital Association is incorporated herein by reference: An Ounce of Prevention: Waste Reduction Strategies for Health Care Facilities, AHA Catalog no. W5-057007, 1993.

b. Copies may be obtained from American Hospital Association, One North Franklin, Chicago, IL 60606; telephone (800) 242-2626.

10. Bay Area Air Quality Management District (BAAQMD).

a. The following documents from the Bay Area Air Quality Management District are incorporated herein by reference:

(1) Method 41, "Determination of Volatile Organic Compounds in Solvent-Based Coatings and Related Materials Containing Parachlorobenzotrifluoride" (December 20, 1995).

(2) Method 43, "Determination of Volatile Methylsiloxanes in Solvent-Based Coatings, Inks, and Related Materials" (November 6, 1996).

b. Copies may be obtained from Bay Area Air Quality Management District, 939 Ellis Street, San Francisco, CA 94109, telephone (415) 771-6000.

11. South Coast Air Quality Management District (SCAQMD).

a. The following documents from the South Coast Air Quality Management District are incorporated herein by reference:

(1) Method 303-91, "Determination of Exempt Compounds," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(2) Method 318-95, "Determination of Weight Percent Elemental Metal in Coatings by X-Ray Diffraction," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(3) Rule 1174 Ignition Method Compliance Certification Protocol (February 28, 1991).

(4) Method 304-91, "Determination of Volatile Organic Compounds (VOC) in Various Materials," in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(5) Method 316A-92, "Determination of Volatile Organic Compounds (VOC) in Materials Used for Pipes and Fittings" in Manual SSMLLABM, "Laboratory Methods of Analysis for Enforcement Samples" (1996).

(6) "General Test Method for Determining Solvent Losses from Spray Gun Cleaning Systems," October 3, 1989.

b. Copies may be obtained from South Coast Air Quality Management District, 21865 E. Copley Drive, Diamond Bar, CA 91765, telephone (909) 396-2000.

12. California Air Resources Board (CARB).

a. The following documents from the California Air Resources Board are incorporated herein by reference:

(1) Test Method 510, "Automatic Shut-Off Test Procedure for Spill-Proof Systems and Spill-Proof Spouts" (July 6, 2000).

(2) Test Method 511, "Automatic Closure Test Procedure for Spill-Proof Systems and Spill-Proof Spouts" (July 6, 2000).

(3) Method 100, "Procedures for Continuous Gaseous Emission Stack Sampling" (July 28, 1997).

(4) Test Method 513, "Determination of Permeation Rate for Spill-Proof Systems" (July 6, 2000).

(5) Method 310, "Determination of Volatile Organic Compounds (VOC) in Consumer Products and Reactive Organic Compounds in Aerosol Coating Products (Including Appendices A and B)" (May 5, 2005).

(6) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 1, § 94503.5 (2003).

(7) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 2, §§ 94509 and 94511 (2003).

(8) California Code of Regulations, Title 17, Division 3, Chapter 1, Subchapter 8.5, Article 4, §§ 94540-94555 (2003).

(9) "Certification Procedure 501 for Portable Fuel Containers and Spill-Proof Spouts, CP-501" (July 26, 2006).

(10) "Test Procedure for Determining Integrity of Spill-Proof Spouts and Spill-Proof Systems, TP-501" (July 26, 2006).

(11) "Test Procedure for Determining Diurnal Emissions from Portable Fuel Containers, TP-502" (July 26, 2006).

b. Copies may be obtained from California Air Resources Board, P.O. Box 2815, Sacramento, CA 95812, telephone (906) 322-3260 or (906) 322-2990.

13. American Architectural Manufacturers Association.

a. The following documents from the American Architectural Manufacturers Association are incorporated herein by reference:

(1) Voluntary Specification 2604-02, "Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels" (2002).

(2) Voluntary Specification 2605-02, "Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels" (2002).

b. Copies may be obtained from American Architectural Manufacturers Association, 1827 Walden Office Square, Suite 550, Schaumburg, IL 60173, telephone (847) 303-5664.

14. American Furniture Manufacturers Association.

a. The following document from the American Furniture Manufacturers Association is incorporated herein by reference: Joint Industry Fabrics Standards Committee, Woven and Knit Residential Upholstery Fabric Standards and Guidelines (January 2001).

b. Copies may be obtained from American Furniture Manufacturers Association, P.O. Box HP-7, High Point, NC 27261; telephone (336) 884-5000.

15. Petroleum Equipment Institute.

a. The following document from the Petroleum Equipment Institute is incorporated herein by reference: Recommended Practices for Installation and Testing of Vapor-Recovery Systems at Vehicle-Fueling Sites, PEI/RP300-09 (2009).

b. Copies may be obtained from Petroleum Equipment Institute, 6931 S. 66th E. Avenue, Suite 310, Tulsa, OK 74133; telephone (918) 494-9696; www.pei.org.

16. American Architectural Manufacturers Association (AAMA).

a. The following documents from the American Architectural Manufacturers Association are incorporated herein by reference:

(1) Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels, publication number AAMA 2604-05.

(2) Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels, publication number AAMA 2605-05.

b. Copies may be obtained from American Architectural Manufacturers Association, 1827 Walden Office Square, Suite 550, Schaumburg, IL 60173-4268; telephone (847) 303-5774.

9VAC5-40-5970. Reporting and recordkeeping.

A. With regard to the emissions standards in 9VAC5-40-5940 and 9VAC5-40-5945, the provisions of 9VAC5-40-50 (Notification, records and reporting) apply.

B. With regard to the emission limits in 9VAC5-40-5935 and 9VAC5-40-5955, the following provisions apply:

1. 9VAC5-40-50 F and H;

2. 40 CFR 60.7; and

3. 40 CFR 60.38f(a) through (m) (n) except as provided in 40 CFR 60.24 and 40 CFR 60.38f(d)(2), and 40 CFR 60.39f(a) through (j).

Article 5
Environmental Protection Agency Standards of Performance for New Stationary Sources (Rule 5-5)

9VAC5-50-400. General.

The U.S. Environmental Protection Agency Regulations on Standards of Performance for New Stationary Sources (NSPSs), as promulgated in 40 CFR Part 60 and designated in 9VAC5-50-410 are, unless indicated otherwise, incorporated by reference into the regulations of the board as amended by the word or phrase substitutions given in 9VAC5-50-420. The complete text of the subparts in 9VAC5-50-410 incorporated in this regulation by reference is contained in 40 CFR Part 60. The 40 CFR section numbers appearing under each subpart in 9VAC5-50-410 identify the specific provisions of the subpart incorporated by reference. The specific version of the provision adopted by reference shall be that contained in the CFR (2019) (2020) in effect July 1, 2019 2020. In making reference to the Code of Federal Regulations, 40 CFR Part 60 means Part 60 of Title 40 of the Code of Federal Regulations; 40 CFR 60.1 means 60.1 in Part 60 of Title 40 of the Code of Federal Regulations.

9VAC5-50-410. Designated standards of performance.

Subpart A - General Provisions.

40 CFR 60.1 through 40 CFR 60.3, 40 CFR 60.7, 40 CFR 60.8, 40 CFR 60.11 through 40 CFR 60.15, 40 CFR 60.18 through 40 CFR 60.19

(applicability, definitions, units and abbreviations, notification and recordkeeping, performance tests, compliance, circumvention, monitoring requirements, modification, reconstruction, general control device requirements, and general notification and reporting requirements)

Subpart B - Not applicable.

Subpart C - Not applicable.

Subpart Ca - Reserved.

Subpart Cb - Not applicable.

Subpart Cc - Not applicable.

Subpart Cd - Not applicable.

Subpart Ce - Not applicable.

Subpart D - Fossil Fuel-Fired Steam Generators.

40 CFR 60.40 through 40 CFR 60.46

(fossil fuel-fired steam generating units of more than 250 million Btu per hour heat input rate and fossil fuel-fired and wood residue-fired steam generating units capable of firing fossil fuel at a heat input rate of more than 250 million Btu per hour)

Subpart Da - Electric Utility Steam Generating Units.

40 CFR 60.40Da through 40 CFR 60.52Da

(electric utility steam generating units capable of combusting more than 250 million Btu per hour heat input of fossil fuel (either alone or in combination with any other fuel), and for which construction, reconstruction, or modification is commenced after September 18, 1978)

Subpart Db - Industrial-Commercial-Institutional Steam Generating Units.

40 CFR 60.40b through 40 CFR 60.49b

(industrial-commercial-institutional steam generating units which have a heat input capacity from combusted fuels of more than 100 million Btu per hour)

Subpart Dc - Small Industrial-Commercial-Institutional Steam Generating Units.

40 CFR 60.40c through 40 CFR 60.48c

(industrial-commercial-institutional steam generating units which have a heat input capacity of 100 million Btu per hour or less, but greater than or equal to 10 million Btu per hour)

Subpart E - Incinerators.

40 CFR 60.50 through 40 CFR 60.54

(incinerator units of more than 50 tons per day charging rate)

Subpart Ea - Municipal Waste Combustors for which Construction is Commenced after December 20, 1989, and on or before September 20, 1994.

40 CFR 60.50a through 40 CFR 60.59a

(municipal waste combustor units with a capacity greater than 250 tons per day of municipal-type solid waste or refuse-derived fuel)

Subpart Eb - Large Municipal Combustors for which Construction is Commenced after September 20, 1994, or for which Modification or Reconstruction is Commenced after June 19, 1996.

40 CFR 60.50b through 40 CFR 60.59b

(municipal waste combustor units with a capacity greater than 250 tons per day of municipal-type solid waste or refuse-derived fuel)

Subpart Ec - Hospital/Medical/Infectious Waste Incinerators for which Construction is Commenced after June 20, 1996.

40 CFR 60.50c through 40 CFR 60.58c

(hospital/medical/infectious waste incinerators that combust any amount of hospital waste and medical/infectious waste or both)

Subpart F - Portland Cement Plants.

40 CFR 60.60 through 40 CFR 60.66

(kilns, clinker coolers, raw mill systems, finish mill systems, raw mill dryers, raw material storage, clinker storage, finished product storage, conveyor transfer points, bagging and bulk loading and unloading systems)

Subpart G - Nitric Acid Plants.

40 CFR 60.70 through 40 CFR 60.74

(nitric acid production units)

Subpart Ga - Nitric Acid Plants for which Construction, Reconstruction, or Modification Commenced after October 14, 2011.

40 CFR 60.70a through 40 CFR 60.77a

(nitric acid production units producing weak nitric acid by either the pressure or atmospheric pressure process)

Subpart H - Sulfuric Acid Plants.

40 CFR 60.80 through 40 CFR 60.85

(sulfuric acid production units)

Subpart I - Hot Mix Asphalt Facilities.

40 CFR 60.90 through 40 CFR 60.93

(dryers; systems for screening, handling, storing and weighing hot aggregate; systems for loading, transferring and storing mineral filler; systems for mixing asphalt; and the loading, transfer and storage systems associated with emission control systems)

Subpart J - Petroleum Refineries.

40 CFR 60.100 through 40 CFR 60.106

(fluid catalytic cracking unit catalyst regenerators, fluid catalytic cracking unit incinerator-waste heat boilers and fuel gas combustion devices)

Subpart Ja - Petroleum Refineries for which Construction, Reconstruction, or Modification Commenced after May 14, 2007.

40 CFR 60.100a through 40 CFR 60.109a

(fluid catalytic cracking units, fluid coking units, delayed coking units, fuel gas combustion devices, including flares and process heaters, and sulfur recovery plants)

Subpart K - Storage Vessels for Petroleum Liquids for which Construction, Reconstruction, or Modification Commenced after June 11, 1973, and prior to May 19, 1978.

40 CFR 60.110 through 40 CFR 60.113

(storage vessels with a capacity greater than 40,000 gallons)

Subpart Ka - Storage Vessels for Petroleum Liquids for which Construction, Reconstruction, or Modification Commenced after May 18, 1978, and prior to July 23, 1984.

40 CFR 60.110a through 40 CFR 60.115a

(storage vessels with a capacity greater than 40,000 gallons)

Subpart Kb - Volatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for which Construction, Reconstruction, or Modification Commenced after July 23, 1984.

40 CFR 60.110b through 40 CFR 60.117b

(storage vessels with capacity greater than or equal to 10,566 gallons)

Subpart L - Secondary Lead Smelters.

40 CFR 60.120 through 40 CFR 60.123

(pot furnaces of more than 550 pound charging capacity, blast (cupola) furnaces and reverberatory furnaces)

Subpart M - Secondary Brass and Bronze Production Plants.

40 CFR 60.130 through 40 CFR 60.133

(reverberatory and electric furnaces of 2205 pound or greater production capacity and blast (cupola) furnaces of 550 pounds per hour or greater production capacity)

Subpart N - Primary Emissions from Basic Oxygen Process Furnaces for which Construction is Commenced after June 11, 1973.

40 CFR 60.140 through 40 CFR 60.144

(basic oxygen process furnaces)

Subpart Na - Secondary Emissions from Basic Oxygen Process Steelmaking Facilities for which Construction is Commenced after January 20, 1983.

40 CFR 60.140a through 40 CFR 60.145a

(facilities in an iron and steel plant: top-blown BOPFs and hot metal transfer stations and skimming stations used with bottom-blown or top-blown BOPFs)

Subpart O - Sewage Treatment Plants.

40 CFR 60.150 through 40 CFR 60.154

(incinerators that combust wastes containing more than 10% sewage sludge (dry basis) produced by municipal sewage treatment plants or incinerators that charge more than 2205 pounds per day municipal sewage sludge (dry basis))

Subpart P - Primary Copper Smelters.

40 CFR 60.160 through 40 CFR 60.166

(dryers, roasters, smelting furnaces, and copper converters)

Subpart Q - Primary Zinc Smelters.

40 CFR 60.170 through 40 CFR 60.176

(roasters and sintering machines)

Subpart R - Primary Lead Smelters

40 CFR 60.180 through 40 CFR 60.186

(sintering machines, sintering machine discharge ends, blast furnaces, dross reverberatory furnaces, electric smelting furnaces and converters)

Subpart S - Primary Aluminum Reduction Plants.

40 CFR 60.190 through 40 CFR 60.195

(potroom groups and anode bake plants)

Subpart T - Phosphate Fertilizer Industry: Wet-Process Phosphoric Acid Plants.

40 CFR 60.200 through 40 CFR 60.205

(reactors, filters, evaporators, and hot wells)

Subpart U - Phosphate Fertilizer Industry: Superphosphoric Acid Plants.

40 CFR 60.210 through 40 CFR 60.215

(evaporators, hot wells, acid sumps, and cooling tanks)

Subpart V - Phosphate Fertilizer Industry: Diammonium Phosphate Plants.

40 CFR 60.220 through 40 CFR 60.225

(reactors, granulators, dryers, coolers, screens, and mills)

Subpart W - Phosphate Fertilizer Industry: Triple Superphosphate Plants.

40 CFR 60.230 through 40 CFR 60.235

(mixers, curing belts (dens), reactors, granulators, dryers, cookers, screens, mills, and facilities which store run-of-pile triple superphosphate)

Subpart X - Phosphate Fertilizer Industry: Granular Triple Superphosphate Storage Facilities.

40 CFR 60.240 through 40 CFR 60.245

(storage or curing piles, conveyors, elevators, screens and mills)

Subpart Y - Coal Preparation and Processing Plants.

40 CFR 60.250 through 40 CFR 60.258

(plants which process more than 200 tons per day: thermal dryers, pneumatic coal-cleaning equipment (air tables), coal processing and conveying equipment (including breakers and crushers), coal storage systems, and coal transfer and loading systems)

Subpart Z - Ferroalloy Production Facilities.

40 CFR 60.260 through 40 CFR 60.266

(electric submerged arc furnaces which produce silicon metal, ferrosilicon, calcium silicon, silicomanganese zirconium, ferrochrome silicon, silvery iron, high-carbon ferrochrome, charge chrome, standard ferromanganese, silicomanganese, ferromanganese silicon or calcium carbide; and dust-handling equipment)

Subpart AA - Steel Plants: Electric Arc Furnaces Constructed after October 21, 1974, and on or before August 17, 1983.

40 CFR 60.270 through 40 CFR 60.276

(electric arc furnaces and dust-handling systems that produce carbon, alloy or specialty steels)

Subpart AAa - Steel Plants: Electric Arc Furnaces and Argon-Oxygen Decarburization Vessels Constructed after August 17, 1983.

40 CFR 60.270a through 40 CFR 60.276a

(electric arc furnaces, argon-oxygen decarburization vessels, and dust-handling systems that produce carbon, alloy, or specialty steels)

Subpart BB - Kraft Pulp Mills.

40 CFR 60.280 through 40 CFR 60.285

(digester systems, brown stock washer systems, multiple effect evaporator systems, black liquor oxidation systems, recovery furnaces, smelt dissolving tanks, lime kilns, condensate strippers and kraft pulping operations)

Subpart BBa - Kraft Pulp Mill Affected Sources for which Construction, Reconstruction, or Modification Commenced after May 23, 2013.

40 CFR 60.280a through 40 CFR 60.288a

(digester systems, brown stock washer systems, multiple effect evaporator systems, black liquor oxidation systems, recovery furnaces, smelt dissolving tanks, lime kilns, condensate strippers, and kraft pulping operations)

Subpart CC - Glass Manufacturing Plants.

40 CFR 60.290 through 40 CFR 60.296

(glass melting furnaces)

Subpart DD - Grain Elevators.

40 CFR 60.300 through 40 CFR 60.304

(grain terminal elevators/grain storage elevators: truck unloading stations, truck loading stations, barge and ship unloading stations, barge and ship loading stations, railcar unloading stations, railcar loading stations, grain dryers, and all grain handling operations)

Subpart EE - Surface Coating of Metal Furniture.

40 CFR 60.310 through 40 CFR 60.316

(metal furniture surface coating operations in which organic coatings are applied)

Subpart FF - Reserved.

Subpart GG - Stationary Gas Turbines.

40 CFR 60.330 through 40 CFR 60.335

(stationary gas turbines with a heat input at peak load equal to or greater than 10 million Btu per hour, based on the lower heating value of the fuel fired)

Subpart HH - Lime Manufacturing Plants.

40 CFR 60.340 through 40 CFR 60.344

(each rotary lime kiln)

Subparts II through JJ - Reserved.

Subpart KK - Lead-Acid Battery Manufacturing Plants.

40 CFR 60.370 through 40 CFR 60.374

(lead-acid battery manufacturing plants that produce or have the design capacity to produce in one day (24 hours) batteries containing an amount of lead equal to or greater than 6.5 tons: grid casting facilities, paste mixing facilities, three-process operation facilities, lead oxide manufacturing facilities, lead reclamation facilities, and other lead-emitting operations)

Subpart LL - Metallic Mineral Processing Plants.

40 CFR 60.380 through 40 CFR 60.386

(each crusher and screen in open-pit mines; each crusher, screen, bucket elevator, conveyor belt transfer point, thermal dryer, product packaging station, storage bin, enclosed storage area, truck loading station, truck unloading station, railcar loading station, and railcar unloading station at the mill or concentrator with the following exceptions. All facilities located in underground mines are exempted from the provisions of this subpart. At uranium ore processing plants, all facilities subsequent to and including the beneficiation of uranium ore are exempted from the provisions of this subpart)

Subpart MM - Automobile and Light Duty Truck Surface Coating Operations.

40 CFR 60.390 through 40 CFR 60.397

(prime coat operations, guide coat operations, and top-coat operations)

Subpart NN - Phosphate Rock Plants.

40 CFR 60.400 through 40 CFR 60.404

(phosphate rock plants which have a maximum plant production capacity greater than four tons per hour: dryers, calciners, grinders, and ground rock handling and storage facilities, except those facilities producing or preparing phosphate rock solely for consumption in elemental phosphorous production)

Subpart OO - Reserved.

Subpart PP - Ammonium Sulfate Manufacture.

40 CFR 60.420 through 40 CFR 60.424

(ammonium sulfate dryer within an ammonium sulfate manufacturing plant in the caprolactam by-product, synthetic, and coke oven by-product sectors of the ammonium sulfate industry)

Subpart QQ - Graphic Arts Industry: Publication Rotogravure Printing.

40 CFR 60.430 through 40 CFR 60.435

(publication rotogravure printing presses, except proof presses)

Subpart RR - Pressure Sensitive Tape and Label Surface Coating Operations.

40 CFR 60.440 through 40 CFR 60.447

(pressure sensitive tape and label material coating lines)

Subpart SS - Industrial Surface Coating: Large Appliances.

40 CFR 60.450 through 40 CFR 60.456

(surface coating operations in large appliance coating lines)

Subpart TT - Metal Coil Surface Coating.

40 CFR 60.460 through 40 CFR 60.466

(metal coil surface coating operations: each prime coat operation, each finish coat operation, and each prime and finish coat operation combined when the finish coat is applied wet on wet over the prime coat and both coatings are cured simultaneously)

Subpart UU - Asphalt Processing and Asphalt Roofing Manufacture.

40 CFR 60.470 through 40 CFR 60.474

(each saturator and each mineral handling and storage facility at asphalt roofing plants; and each asphalt storage tank and each blowing still at asphalt processing plants, petroleum refineries, and asphalt roofing plants)

Subpart VV - Equipment Leaks of Volatile Organic Compounds in the Synthetic Organic Chemicals Manufacturing Industry for which Construction, Reconstruction, or Modification Commenced after January 5, 1981, and on or before November 7, 2006.

40 CFR 60.480 through 40 CFR 60.489

(all equipment within a process unit in a synthetic organic chemicals manufacturing plant)

Subpart VVa - Equipment Leaks of VOC in the Synthetic Organic Chemicals Manufacturing Industry for which Construction, Reconstruction, or Modification Commenced after November 7, 2006.

40 CFR 60.480a through 40 CFR 60.489a

(all equipment within a process unit in a synthetic organic chemicals manufacturing plant)

Subpart WW - Beverage Can Surface Coating Industry.

40 CFR 60.490 through 40 CFR 60.496

(beverage can surface coating lines: each exterior base coat operation, each overvarnish coating operation, and each inside spray coating operation)

Subpart XX - Bulk Gasoline Terminals.

40 CFR 60.500 through 40 CFR 60.506

(total of all loading racks at a bulk gasoline terminal which deliver liquid product into gasoline tank trucks)

Subparts YY through ZZ - Reserved.

Subpart AAA - New Residential Wood Heaters.

40 CFR 60.530 through 40 CFR 60.539b

(NOTE: In accordance with Chapter 471 of the 2015 Acts of Assembly, authority to enforce the above standard is being retained by EPA and the standard is not incorporated by reference into these regulations. A state permit may be required of certain facilities if the provisions of 9VAC5-50 and 9VAC5-80 apply. Owners should review those provisions and contact the appropriate regional office for guidance on whether those provisions apply.)

Subpart BBB - Rubber Tire Manufacturing Industry.

40 CFR 60.540 through 40 CFR 60.548

(each undertread cementing operation, each sidewall cementing operation, each tread end cementing operation, each bead cementing operation, each green tire spraying operation, each Michelin-A operation, each Michelin-B operation, and each Michelin-C automatic operation)

Subpart CCC - Reserved.

Subpart DDD - Volatile Organic Compound (VOC) Emissions from the Polymer Manufacturing Industry.

40 CFR 60.560 through 40 CFR 60.566

(for polypropylene and polyethylene manufacturing using a continuous process that emits continuously or intermittently: all equipment used in the manufacture of these polymers. For polystyrene manufacturing using a continuous process that emits continuously: each material recovery section. For poly(ethylene terephthalate) manufacturing using a continuous process that emits continuously: each polymerization reaction section; if dimethyl terephthalate is used in the process, each material recovery section is also an affected facility; if terephthalic acid is used in the process, each raw materials preparation section is also an affected facility. For VOC emissions from equipment leaks: each group of fugitive emissions equipment within any process unit, excluding poly(ethylene terephthalate) manufacture.)

Subpart EEE - Reserved.

Subpart FFF - Flexible Vinyl and Urethane Coating and Printing.

40 CFR 60.580 through 40 CFR 60.585

(each rotogravure printing line used to print or coat flexible vinyl or urethane products)

Subpart GGG - Equipment Leaks of VOC in Petroleum Refineries for which Construction, Reconstruction, or Modification Commenced after January 4, 1983, and on or before November 7, 2006.

40 CFR 60.590 through 40 CFR 60.593

(each compressor, valve, pump pressure relief device, sampling connection system, open-ended valve or line, and flange or other connector in VOC service)

Subpart GGGa - Equipment Leaks of VOC in Petroleum Refineries for which Construction, Reconstruction, or Modification Commenced after November 7, 2006.

40 CFR 60.590a through 40 CFR 60.593a

(each compressor, valve, pump pressure relief device, sampling connection system, open-ended valve or line, and flange or other connector in VOC service)

Subpart HHH - Synthetic Fiber Production Facilities.

40 CFR 60.600 through 40 CFR 60.604

(each solvent-spun synthetic fiber process that produces more than 500 megagrams of fiber per year)

Subpart III - Volatile Organic Compound (VOC) Emissions from the Synthetic Organic Chemical Manufacturing Industry (SOCMI) Air Oxidation Unit Processes.

40 CFR 60.610 through 40 CFR 60.618

(each air oxidation reactor not discharging its vent stream into a recovery system and each combination of an air oxidation reactor or two or more air oxidation reactors and the recovery system into which the vent streams are discharged)

Subpart JJJ - Petroleum Dry Cleaners.

40 CFR 60.620 through 40 CFR 60.625

(facilities located at a petroleum dry cleaning plant with a total manufacturers' rated dryer capacity equal to or greater than 84 pounds: petroleum solvent dry cleaning dryers, washers, filters, stills, and settling tanks)

Subpart KKK - Equipment Leaks of VOC from Onshore Natural Gas Processing Plants for which Construction, Reconstruction, or Modification Commenced after January 20, 1984, and on or before August 23, 2011.

40 CFR 60.630 through 40 CFR 60.636

(each compressor in VOC service or in wet gas service; each pump, pressure relief device, open-ended valve or line, valve, and flange or other connector that is in VOC service or in wet gas service, and any device or system required by this subpart)

Subpart LLL - Sulfur Dioxide Emissions from Onshore Natural Gas Processing for which Construction, Reconstruction, or Modification Commenced after January 20, 1984, and on or before August 23, 2011.

40 CFR 60.640 through 40 CFR 60.648

(facilities that process natural gas: each sweetening unit, and each sweetening unit followed by a sulfur recovery unit)

Subpart MMM - Reserved.

Subpart NNN - Volatile Organic Compound (VOC) Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Distillation Operations.

40 CFR 60.660 through 40 CFR 60.668

(each distillation unit not discharging its vent stream into a recovery system, each combination of a distillation unit or of two or more units and the recovery system into which their vent streams are discharged)

Subpart OOO - Nonmetallic Mineral Processing Plants.

40 CFR 60.670 through 40 CFR 60.676

(facilities in fixed or portable nonmetallic mineral processing plants: each crusher, grinding mill, screening operation, bucket elevator, belt conveyor, bagging operation, storage bin, enclosed truck or railcar loading station)

Subpart PPP - Wool Fiberglass Insulation Manufacturing Plants.

40 CFR 60.680 through 40 CFR 60.685

(each rotary spin wool fiberglass insulation manufacturing line)

Subpart QQQ - VOC Emissions from Petroleum Refinery Wastewater Systems.

40 CFR 60.690 through 40 CFR 60.699

(individual drain systems, oil-water separators, and aggregate facilities in petroleum refineries)

Subpart RRR - Volatile Organic Compound Emissions from Synthetic Organic Chemical Manufacturing Industry (SOCMI) Reactor Processes.

40 CFR 60.700 through 40 CFR 60.708

(each reactor process not discharging its vent stream into a recovery system, each combination of a reactor process and the recovery system into which its vent stream is discharged, and each combination of two or more reactor processes and the common recovery system into which their vent streams are discharged)

Subpart SSS - Magnetic Tape Coating Facilities.

40 CFR 60.710 through 40 CFR 60.718

(each coating operation and each piece of coating mix preparation equipment)

Subpart TTT - Industrial Surface Coating: Surface Coating of Plastic Parts for Business Machines.

40 CFR 60.720 through 40 CFR 60.726

(each spray booth in which plastic parts for use in the manufacture of business machines receive prime coats, color coats, texture coats, or touch-up coats)

Subpart UUU - Calciners and Dryers in Mineral Industries.

40 CFR 60.730 through 40 CFR 60.737

(each calciner and dryer at a mineral processing plant)

Subpart VVV - Polymeric Coating of Supporting Substrates Facilities.

40 CFR 60.740 through 40 CFR 60.748

(each coating operation and any onsite coating mix preparation equipment used to prepare coatings for the polymeric coating of supporting substrates)

Subpart WWW - Municipal Solid Waste Landfills.

40 CFR 60.750 through 40 CFR 60.759

(municipal solid waste landfills for the containment of household and Resource Conservation and Recovery Act (RCRA) Subtitle D wastes)

Subpart XXX - Municipal Solid Waste Landfills that Commenced Construction, Reconstruction, or Modification After July 17, 2014

40 CFR 60.760 through 40 CFR 60.769

(municipal solid waste landfills for the containment of household and RCRA Subtitle D wastes)

Subpart AAAA - Small Municipal Waste Combustors for which Construction is Commenced after August 30, 1999, or for which Modification or Reconstruction is Commenced after June 6, 2001.

40 CFR 60.1000 through 40 CFR 60.1465

(municipal waste combustor units with a capacity less than 250 tons per day and greater than 35 tons per day of municipal solid waste or refuse-derived fuel)

Subpart BBBB - Not applicable.

Subpart CCCC - Commercial/Industrial Solid Waste Incinerators.

40 CFR 60.2000 through 40 CFR 60.2265

(an enclosed device using controlled flame combustion without energy recovery that is a distinct operating unit of any commercial or industrial facility, or an air curtain incinerator without energy recovery that is a distinct operating unit of any commercial or industrial facility)

Subpart DDDD - Not applicable.

Subpart EEEE - Other Solid Waste Incineration Units for which Construction is Commenced after December 9, 2004, or for which Modification or Reconstruction is Commenced on or after June 16, 2006.

40 CFR 60.2880 through 40 CFR 60.2977

(very small municipal waste combustion units with the capacity to combust less than 35 tons per day of municipal solid waste or refuse-derived fuel, and institutional waste incineration units owned or operated by an organization having a governmental, educational, civic, or religious purpose)

Subpart FFFF - Reserved.

Subpart GGGG - Reserved.

Subpart HHHH - Reserved.

Subpart IIII - Stationary Compression Ignition Internal Combustion Engines.

40 CFR 60.4200 through 40 CFR 60.4219

(NOTE: Authority to enforce the above standard is being retained by EPA and the standard is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)

Subpart JJJJ - Stationary Spark Ignition Internal Combustion Engines.

40 CFR 60.4230 through 40 CFR 60.4248

(NOTE: Authority to enforce the above standard is being retained by EPA and the standard is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)

Subpart KKKK - Stationary Combustion Turbines.

40 CFR 60.4300 through 40 CFR 60.4420

(stationary combustion turbine with a heat input at peak load equal to or greater than 10.7 gigajoules (10 MMBtu) per hour)

Subpart LLLL - Sewage Sludge Incineration Units.

40 CFR 60.4760 through 40 CFR 60.4925

(an incineration unit combusting sewage sludge for the purpose of reducing the volume of the sewage sludge by removing combustible matter, including the sewage sludge feed system, auxiliary fuel feed system, grate system, flue gas system, waste heat recovery equipment, and bottom ash system; and all ash handling systems connected with the bottom ash handling system)

Subpart MMMM - Reserved.

Subpart NNNN - Reserved.

Subpart OOOO - Crude Oil and Natural Gas Production, Transmission and Distribution for which Construction, Modification, or Reconstruction Commenced after August 23, 2011, and on or before September 18, 2015.

40 CFR 60.5360 through 40 CFR 60.5499

(facilities that operate gas wells, centrifugal compressors, reciprocating compressors, pneumatic controllers, and storage vessels)

Subpart OOOOa - Crude Oil and Natural Gas Facilities for which Construction, Modification, or Reconstruction Commenced after September 18, 2015.

40 CFR 60.5360a through 40 CFR 60.5499a

(NOTE: Authority to enforce the above standard is being retained by EPA and it is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80. (facilities that operate gas wells, centrifugal compressors, reciprocating compressors, pneumatic controllers and pumps, storage vessels, and sweetening units)

Subpart PPPP - Reserved.

Subpart QQQQ - New Residential Hydronic Heaters and Forced-Air Furnaces

40 CFR 60.5472 through 40 CFR 60.5483

(NOTE: In accordance with Chapter 471 of the 2015 Acts of Assembly, authority to enforce the above standard is being retained by EPA and the standard is not incorporated by reference into these regulations. A state permit may be required of certain facilities if the provisions of 9VAC5-50 and 9VAC5-80 apply. Owners should review those provisions and contact the appropriate regional office for guidance on whether those provisions apply.)

Subpart RRRR - Reserved.

Subpart SSSS - Reserved.

Subpart TTTT - Reserved.

Appendix A - Test methods.

Appendix B - Performance specifications.

Appendix C - Determination of Emission Rate Change.

Appendix D - Required Emission Inventory Information.

Appendix E - Reserved.

Appendix F - Quality Assurance Procedures.

Appendix G - Not applicable.

Appendix H - Reserved.

Appendix I - Removable label and owner's manual.

Part II
Emission Standards

Article 1
Environmental Protection Agency National Emission Standards for Hazardous Air Pollutants (Rule 6-1)

9VAC5-60-60. General.

The Environmental Protection Agency (EPA) Regulations on National Emission Standards for Hazardous Air Pollutants (NESHAP), as promulgated in 40 CFR Part 61 and designated in 9VAC5-60-70 are, unless indicated otherwise, incorporated by reference into the regulations of the board as amended by the word or phrase substitutions given in 9VAC5-60-80. The complete text of the subparts in 9VAC5-60-70 incorporated in this regulation by reference is contained in 40 CFR Part 61. The 40 CFR section numbers appearing under each subpart in 9VAC5-60-70 identify the specific provisions of the subpart incorporated by reference. The specific version of the provision adopted by reference shall be that contained in the CFR (2019) (2020) in effect July 1, 2019 2020. In making reference to the Code of Federal Regulations, 40 CFR Part 61 means Part 61 of Title 40 of the Code of Federal Regulations; 40 CFR 61.01 means 61.01 in Part 61 of Title 40 of the Code of Federal Regulations.

Article 2
Environmental Protection Agency National Emission Standards for Hazardous Air Pollutants for Source Categories (Rule 6-2)

9VAC5-60-90. General.

The Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants for Source Categories (Maximum Achievable Control Technologies, or MACTs) as promulgated in 40 CFR Part 63 and designated in 9VAC5-60-100 are, unless indicated otherwise, incorporated by reference into the regulations of the board as amended by the word or phrase substitutions given in 9VAC5-60-110. The complete text of the subparts in 9VAC5-60-100 incorporated in this regulation by reference is contained in 40 CFR Part 63. The 40 CFR section numbers appearing under each subpart in 9VAC5-60-100 identify the specific provisions of the subpart incorporated by reference. The specific version of the provision adopted by reference shall be that contained in the CFR (2019) (2020) in effect July 1, 2019 2020. In making reference to the Code of Federal Regulations, 40 CFR Part 63 means Part 63 of Title 40 of the Code of Federal Regulations; 40 CFR 63.1 means 63.1 in Part 63 of Title 40 of the Code of Federal Regulations.